| Page 60 of 111 |
CraweN
Posts: 719
Location: Upside down in chair
|
 Posted: Thu, 29th Sep 2011 07:04 Post subject: |
|
 |
Seing as this is about hacking the xbox 360 I thought I might throw this in here.
A while aback I tried updating the firmware on my liteon using my onboard chipset, not a VIA chipset though, and the xbox as my power source for the drive.
After some problems I got it into vendor mode and grabbed the key, made a new firmware, erased the drive and while writing the new firmware on bank 3 jungleflasher stopped responding.
Afterwards I was unable to get the drive in vendor mode again. So I bought myself a maximus extractor pro so I could power toggle without using my xbox. Also I've just bought a VIA chipset and hope I will be able to get the fucker working again.
Now, I have done some reading about using jungleflasher, Dosflash etc. But was is the easiest way to do this? I need to use the VIA chipset to connect to the liteon, uninstall the drivers for the chipset and just pray I can get it to respond with the right return code.
How do you people do it?
Hardware: Ryzen 3700x, B450 MSI Gaming Pro carbon AC, GTX1080, 32 GB 3200 Mhz cas 14, 256 EVO SSD, 1 TB EVO SSD and 4 TB HDD.
Console: xbox, wii and xbox 360
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 09:52 Post subject: |
|
|
| CraweN wrote: | Seing as this is about hacking the xbox 360 I thought I might throw this in here.
A while aback I tried updating the firmware on my liteon using my onboard chipset, not a VIA chipset though, and the xbox as my power source for the drive.
After some problems I got it into vendor mode and grabbed the key, made a new firmware, erased the drive and while writing the new firmware on bank 3 jungleflasher stopped responding.
Afterwards I was unable to get the drive in vendor mode again. So I bought myself a maximus extractor pro so I could power toggle without using my xbox. Also I've just bought a VIA chipset and hope I will be able to get the fucker working again.
Now, I have done some reading about using jungleflasher, Dosflash etc. But was is the easiest way to do this? I need to use the VIA chipset to connect to the liteon, uninstall the drivers for the chipset and just pray I can get it to respond with the right return code.
How do you people do it? |
did you not just able to hit intro again and that would put it in vendor mode?
i remember when jf froze on me too bk in the day it wasent anything to worry about aslong as you werent in the midddle of a dump
|
|
| Back to top |
|
|
CraweN
Posts: 719
Location: Upside down in chair
|
| Posted: Thu, 29th Sep 2011 10:18 Post subject: |
|
|
Well, I think I partially panicked. The tutorial mentioned you had to be careful when you plugged in the power from the xbox to the liteon. So I was having problems with the timing. I decided to wait thill I had a safer way to switch the power, that was why I got the maximus. I tried again. but this time I couldn't figure out which port the drive was connected to.
Also I was unsure if I sent the commands to the wrong port that I could kill my HDD's?
As you can read I was a bit new to it all.
Hardware: Ryzen 3700x, B450 MSI Gaming Pro carbon AC, GTX1080, 32 GB 3200 Mhz cas 14, 256 EVO SSD, 1 TB EVO SSD and 4 TB HDD.
Console: xbox, wii and xbox 360
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 12:13 Post subject: |
|
|
| CraweN wrote: | Well, I think I partially panicked. The tutorial mentioned you had to be careful when you plugged in the power from the xbox to the liteon. So I was having problems with the timing. I decided to wait thill I had a safer way to switch the power, that was why I got the maximus. I tried again. but this time I couldn't figure out which port the drive was connected to.
Also I was unsure if I sent the commands to the wrong port that I could kill my HDD's?
As you can read I was a bit new to it all. |
Go read the JF tutorial, im sure that'll help you. I have made several mistakes during the times i've flashed my liteon, but it has always worked out - liteon is practically impossible to fuck up beyond repair. (as long as you have your correct key)
|
|
| Back to top |
|
|
Grale
Banned
Posts: 3321
Location: Invert
|
| Posted: Thu, 29th Sep 2011 12:29 Post subject: |
|
|
Does the drive eject as it is? If not just boot up dos flasher, don't worry about the port no dosflash will find all drives connected. Just use the cfw jungleflasher created.
Read dosflash tutorial first it's a doddle mate. I had exact same problem with mine.
MSI X570 Tomahawk |Corsair Vengeance LPX 32gb 3600mhz | Ryzen 5800X3D | EKWB Watercooling | Seasonic Focus GX 850 Gold PSU | 4090 Founders | Predator X34P UW curved monitor | Window Pro 10 x64
|
|
| Back to top |
|
|
CraweN
Posts: 719
Location: Upside down in chair
|
| Posted: Thu, 29th Sep 2011 13:03 Post subject: |
|
|
Jungleflasher crashed while writing the firmware. After that I've been unable to see the drive even when using dosflash. I will try again when I get home. My onboard chipset is Non-VIA chipset, maybe that is why.
Hardware: Ryzen 3700x, B450 MSI Gaming Pro carbon AC, GTX1080, 32 GB 3200 Mhz cas 14, 256 EVO SSD, 1 TB EVO SSD and 4 TB HDD.
Console: xbox, wii and xbox 360
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 14:59 Post subject: |
|
|
That's why i will never use jungle flasher again, too many crash and freeze. Dosflash is 100% safe!
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 16:37 Post subject: |
|
|
I've never used JF for flashing inside Windows. Too scary... DOSFlash all the way!
|
|
| Back to top |
|
|
Grale
Banned
Posts: 3321
Location: Invert
|
| Posted: Thu, 29th Sep 2011 17:07 Post subject: |
|
|
Jungleflasher is always good until i start hooking up a liteon drive.
MSI X570 Tomahawk |Corsair Vengeance LPX 32gb 3600mhz | Ryzen 5800X3D | EKWB Watercooling | Seasonic Focus GX 850 Gold PSU | 4090 Founders | Predator X34P UW curved monitor | Window Pro 10 x64
|
|
| Back to top |
|
|
Horrordee
Soderator
Posts: 8867
Location: England
|
| Posted: Thu, 29th Sep 2011 17:27 Post subject: |
|
|
So, I haven't seen any confirmation of the Samsung drive being completed!?
I have an old Samsung drive, and I wanna play mah GOW3!
Space for rent. Contact me for rates!
|
|
| Back to top |
|
|
cobALT
Posts: 2340
Location: In a world created by fascist and used by cowards to manipulate
|
| Posted: Thu, 29th Sep 2011 17:40 Post subject: |
|
|
So DOSFlash is the way to go if you have a LiteOn?
I usually sent my box to someone for updates but I'm thinking about updating myself this time. I haven't done it before as I didn't had the VIA chipset, but I read that nforce should do fine.
[img:91f1fb12c3 ]http://i.imgur.com/fTzqMvq.gif[/img]
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 18:35 Post subject: |
|
|
| cobALT wrote: | So DOSFlash is the way to go if you have a LiteOn?
I usually sent my box to someone for updates but I'm thinking about updating myself this time. I haven't done it before as I didn't had the VIA chipset, but I read that nforce should do fine. |
I dont think so. As i mentioned before, i've flashed my drive several times, every time using JF, and even though i've managed to fuck up on a few occations JF has always been able to flash my drive.
I am using a VIA chipset though, and i would recomend you do the same.
I would also recomend you ask for help in JF's IRC channel on EFnet, they are usualy very helpful, and have provided me with help a few times
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 18:48 Post subject: |
|
|
| cobALT wrote: | So DOSFlash is the way to go if you have a LiteOn?
I usually sent my box to someone for updates but I'm thinking about updating myself this time. I haven't done it before as I didn't had the VIA chipset, but I read that nforce should do fine. |
and search for tutorials on the net, it's more easy than you think
|
|
| Back to top |
|
|
|
|
|
| Back to top |
|
|
cobALT
Posts: 2340
Location: In a world created by fascist and used by cowards to manipulate
|
| Posted: Thu, 29th Sep 2011 21:11 Post subject: |
|
|
I don't have my key; the guy who did my fw install/updates has it. I am going to ask him to sent it to me, though.
For now I'll just wait for LT+ 2.0/MAX to come out. I'm still on LT+ 1.1 and old dash(I think the last update came with Bulletstorm) so I'm going to have to do the whole dashupdate thing witch sounds a bit tricky. Btw, is there a guide for that, removing the hacked fw and installing the stock one -- people said you shouldn't update until you go back to stock with the fw.
[img:91f1fb12c3 ]http://i.imgur.com/fTzqMvq.gif[/img]
|
|
| Back to top |
|
|
|
|
|
| Back to top |
|
|
cobALT
Posts: 2340
Location: In a world created by fascist and used by cowards to manipulate
|
| Posted: Thu, 29th Sep 2011 21:21 Post subject: |
|
|
So... DOSFlash?
Btw, if you don't have VIA are you using nForce?
[img:91f1fb12c3 ]http://i.imgur.com/fTzqMvq.gif[/img]
|
|
| Back to top |
|
|
|
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 21:42 Post subject: |
|
|
nforce here and flashing liteon phat with jf no problem
3080 | ps5 pro
Sin317-"im 31 years old and still surprised at how much shit comes out of my ass actually ..."
SteamDRM-"Call of Duty is the symbol of the true perfection in every aspect. Call of Duty games are like Mozart's/Beethoven's symphonies"
deadpoetic-"are you new to the cyberspace?"
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 21:43 Post subject: |
|
|
Since you guys are talking about flashing, what would cause the "Access" Error to display on a liteon drive in Jungle-flasher..? I am not at home to give you the exact error but I can describe what happens.....
Basically we start Jungleflasher, connect the drive to the PC using the 360 as the power source.
Then start the process to make a dump of the firmware and several prompts display on the screen at this time. One might say "Power cycle drive and leave tray half open". Then after that is says "Now pull tray all the way out." Right after this message is displayed, I click the progress button to advance and I get an error (sorry I can't remember) and it has to do with the drive still being locked...I guess. This is a phat liteon drive currently flashed with LT 1.9. My friend did some reading and found that you need a probe to get a dump of the firmware. I had thought you only needed one to get the first dump, once the drive is flashed with LT you could do it as many times as you wanted. We did get a dump of the original firmware so we have the key but I want to update his drive and we keep getting this error right before the firmware dump would happen.
Has anybody else had this issue...? Or know what I'm talking about...?
When I get home I'll update my post with the error from JungleFlasher.
|
|
| Back to top |
|
|
CraweN
Posts: 719
Location: Upside down in chair
|
| Posted: Thu, 29th Sep 2011 21:46 Post subject: |
|
|
| sabin1981 wrote: | nForce, VIA or Intel ICH8-9-10 all work just fine for flashing LiteOns (I've tested them all  ) my current Intel ICH9 works great in DOSFlash. |
So you can flash the latest version of lt+ using dosflash? How about extracting the old firmware, or do you still use jungleflasher to create the new firmware?
If its possible, I think I will make a bootable usb with dosflash and disconnect all my harddrives just to be safe.
Hardware: Ryzen 3700x, B450 MSI Gaming Pro carbon AC, GTX1080, 32 GB 3200 Mhz cas 14, 256 EVO SSD, 1 TB EVO SSD and 4 TB HDD.
Console: xbox, wii and xbox 360
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 21:49 Post subject: |
|
|
I flashed LT1.1 in DOSFlash, I can't speak for 1.91 since I'm not running it. I need to get around to ripping my PC/360 apart to flash again. I won't be extracting the old FW either, I have the drive key written down so I'll just inject that into 2.0-Max (when it comes out) FW and flash directly.
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 21:58 Post subject: |
|
|
Any tentative ETA for LT 2.0 Max?
|
|
| Back to top |
|
|
sTo0z
[Moderator] Babysitter
Posts: 7449
Location: USA
|
| Posted: Thu, 29th Sep 2011 22:19 Post subject: |
|
|
JF crashes my Windows 7 install, but works fine with my Windows XP install.
So I always leave my XP install on a separate harddrive and just swap 7 out when I need to flash.
JF always seems to be very picky where I plug my 360 drive in also, if it isn't in the primary SATA then it crashes or doesn't find it.
But if I set it up right, and use my XP install, everything goes and flashes great, takes me about 5 minutes to do a flash, including taking the damn thing apart! 
|
|
| Back to top |
|
|
|
|
|
| Back to top |
|
|
|
|
| Posted: Thu, 29th Sep 2011 23:24 Post subject: |
|
|
| cobALT wrote: | So... DOSFlash?
Btw, if you don't have VIA are you using nForce? |
nForce... but if it does it, it always does either when launching or when selecting the drive... if I pass that point "unharmed" it has never fucked up after that.
|
|
| Back to top |
|
|
|
|
|
| Back to top |
|
|
NFOAC
Posts: 6015
Location: India
|
| Posted: Fri, 30th Sep 2011 03:40 Post subject: |
|
|
I said this before and now this is proven that the fw would be released in 2 batches phat and slim.
[2011-09-29 10:16PM UTC] #fw <mr_1000> so c4eva are the fws going to be alltogether or relased as they are completed?
[2011-09-29 10:16PM UTC] #fw <Al_lee> its coming soon i think
[2011-09-29 10:16PM UTC] #fw <SOL> won’t know till someone gets new dash
[2011-09-29 10:17PM UTC] #fw <nms> i love mookie
[2011-09-29 10:17PM UTC] #fw <nms>
[2011-09-29 10:18PM UTC] #fw <c4eva> non slim,then slim
|
|
| Back to top |
|
|
|
|
| Posted: Fri, 30th Sep 2011 05:33 Post subject: |
|
|
| gibman70 wrote: | | *posts the mundane facepalm gif* |
I guess a one liner would have been better, rather than taking all the pain to post that arsed gif.
|
|
| Back to top |
|
|
|
|
| Posted: Fri, 30th Sep 2011 10:03 Post subject: |
|
|
I cannot play one of the latest releases such as Resident Evil 4 HD because it demands I update the firmware. Is there a way to get around this without having to update and reflash?
I have a Hamachi (unsure on which model as I haven't opened my 360 in a long time) and currently running iXtreme 1.51
|
|
| Back to top |
|
|
| Page 60 of 111 |
All times are GMT + 1 Hour |
