| Page 1 of 1 |
|
|
|
| Back to top |
|
 |
JBeckman
VIP Member
Posts: 34984
Location: Sweden
|
 Posted: Fri, 19th Aug 2016 09:12 Post subject: |
|
|
http://forum.corsair.com/v3/showthread.php?p=664928
| Quote: |
The SATA plug powers the pump so you will need it connected. The 3-pin connector coming out from the H80i is the RPM wire so your BIOS won't give you an error about no fan plugged in to the CPU_FAN port.
Check the threads for the screws on the radiator and see if they are stripped.
|
Unless I'm completely miss-understanding the fan wire is then just there to report a RPM value to the motherboard bios to avoid the boot error with no CPU fan connected?
|
|
| Back to top |
|
|
tonizito
VIP Member
Posts: 51408
Location: Portugal, the shithole of Europe.
|
| Posted: Fri, 19th Aug 2016 09:40 Post subject: |
|
|
I bet a syrian/turk/etc would have plugged that shit in correctly 
| boundle (thoughts on cracking AITD) wrote: | | i guess thouth if without a legit key the installation was rolling back we are all fucking then |
|
|
| Back to top |
|
|
LeoNatan
☢ NFOHump Despot ☢
Posts: 73196
Location: Ramat Gan, Israel 🇮🇱
|
| Posted: Fri, 19th Aug 2016 10:22 Post subject: |
|
|
Try to wash it with soap and water.
|
|
| Back to top |
|
|
|
|
| Posted: Fri, 19th Aug 2016 11:14 Post subject: |
|
|
| JBeckman wrote: | http://forum.corsair.com/v3/showthread.php?p=664928
| Quote: |
The SATA plug powers the pump so you will need it connected. The 3-pin connector coming out from the H80i is the RPM wire so your BIOS won't give you an error about no fan plugged in to the CPU_FAN port.
Check the threads for the screws on the radiator and see if they are stripped.
|
Unless I'm completely miss-understanding the fan wire is then just there to report a RPM value to the motherboard bios to avoid the boot error with no CPU fan connected? |
The sata was plugged in correctly, so that means the pump probably wasn't pumping. Faulty device.
|
|
| Back to top |
|
|
|
|
| Posted: Fri, 19th Aug 2016 11:19 Post subject: |
|
|
A pump that won't pump is probably faulty yes. Just like a hooker who won't hook is faulty.
|
|
| Back to top |
|
|
|
|
| Posted: Fri, 19th Aug 2016 11:22 Post subject: |
|
|
re-test it, you can plug it in without installing it to the CPU, use this time the CPU_FAN header. Check from bios what kind of RPM it says.
|
|
| Back to top |
|
|
|
|
| Posted: Fri, 19th Aug 2016 11:42 Post subject: |
|
|
This is what i've been wanting to try. I just cba installing this crap again. I probably did plug it in correctly.
|
|
| Back to top |
|
|
|
|
|
| Back to top |
|
|
|
|
| Posted: Fri, 19th Aug 2016 12:19 Post subject: |
|
|
Well, called the support where i bought it and getting a h80i v2 shipped. They said i could just throw my old one away, pretty sweet!
|
|
| Back to top |
|
|
| Page 1 of 1 |
All times are GMT + 1 Hour |
Not 100% certain, but if i am to rma it, i should be certain. What significance would it make using opt instead of the regular for such a cooler? If anything, can i quickly plug it in without actually installing it to be sure it's faulty or not?
